LIGHTING

FELED SERIES

• For use in locations where:
— Hazardous areas are designated as Zone 1 and 2 – 21 and 22
— A high degree of corrosion resistance is required
— Protection against dirt, water and moisture is necessary
• Typical applications include:
— Oil refineries
— Petrochemical facilities
— Food processing plants
— Waste and water treatment plants
— Underground tunnels
— General manufacturing facilities

• Available in 5000K or 4000K Color Temperatures.
• Meets photobiological requirement for Risk Group 0 (RG0).
• Easy to retrofit in same mounting footprint as Appleton’s FE series nonmetallic fluorescent luminaires.
• Full range of lumen outputs, with light distribution equivalent to Appleton’s FE series fluorescent luminaires.
• Corrosion-resistant fiberglass reinforced polyester body and hinged polycarbonate lens.
• High impact resistance housing (20 Joules – IK10) from -30 °C to +55 °C (-22 °F to +131 °F) ambient temperature and wind profile for use in extreme offshore and onshore
environments.
• 60,000+ hour LED life for years of maintenance free operation.
• Lightweight design, hinged cover with captive screws, and terminal block wiring for easy installation and maintenance.
• Contemporary, low profile design suitable for tight spaces.
• Standard screw-type terminal block can accept 1.5 to 6 mm2 wire.
• Field replaceable LED driver.
• Industry-leading thermal management for safe, reliable operation over wide temperature range.
• Universal, high efficiency, drivers cover voltage requirements for 120-277 Vac, 170-300 Vdc, 50/60 Hz +/- 10%.
• High power factor electronic driver (>0.95).
• Standard 6KV surge suppression.
• M20 plug or M25 plug provided.
• Latch assembly and elastomer gasket seals against water and dust ingress, IP66.
• Easily accessed for maintenance using Allen key or straight blade screwdriver.
• Central opening with unique patented release system to prevent damage.
• Can be horizontally or vertically mounted.
• Available in 3 hour emergency version, including built-in monthly self- test. Test results through multi-colored LED.
• Positive safety switch disconnects power to LED’s and driver to allow maintenance in hazardous locations (emergency version).
• Ex e battery with plug-in connector

 -30 °C up to +55 °C

ATEX, IECX

0.140A at 230Vac to 0.333A at 230Vac 

FE SERIES

• Can be installed in hazardous areas designated as Zone 1 and 2 – 21 and 22.
• For use in locations where a high degree of corrosion resistance is required.
• For indoor/outdoor use where protection against dirt, water and moisture is necessary.
• Typical applications include oil refineries, petrochemical facilities, pulp and paper mills, food processing plants, warehouses, underground tunnels and general manufacturing facilities.

• Corrosion-resistant fiberglass reinforced polyester body and hinged polycarbonate lens.
• High impact resistance housing (20 Joules – IK10) from -40 °C to +55 °C (-40 °F to +131 °F) ambient temperature and wind profile for use in extreme offshore and onshore environments.
• Latch assembly and elastomer gasket seals against water and dust ingress, IP66/67.
• Easily accessed for maintenance using Allen key or straight blade screwdriver.
• Central opening with unique patented release system to prevent damage.
• Can be horizontally or vertically mounted.
• Hinged parabolic reflector for high lumen output efficiency.
• Vibration resistant spring loaded lampholders for bi-pin (G13) or mono-pin (Fa6) versions.
• Positive safety switch disconnects power to lamps and ballast to allow maintenance in hazardous locations.
• Electronic multi-tap ballast 110 to 254 Vac/Vdc +/- 10P/60 Hz, for global applications. High power factor electronic ballast (>0.95). EOL (End Of Life) protection in accordance to the latest EN/IEC 60079-7 standard.
• Two channel ballast prevents dark areas by allowing one lamp to remain lit if one fails.
• Ballast plug-in with Ex e connector for quick and error-free maintenance.
• Available in 3 hour or 90 minute emergency versions, including multi-tap ballast with built-in monthly self test. Test results through multi-colored LED.
• Ex e battery with plug-in connector.

-40 °C to +55 °C

CE, ATEX, IECX

18W to 58W